The Stahlhelm or the helmet was the most distinctive and recognizable feature of the Germany army uniform, the item that has come to symbolize German militarism in even remotest corners of the world, in both World Wars.
![Stahlhelm, the stages of the helmet-making process of Stahlhelms for the Imperial German Army, 1916](https://www.thevintagenews.com/wp-content/uploads/sites/65/2015/10/Stahlhelm-the-stages-of-the-helmet-making-process-of-Stahlhelms-for-the-Imperial-German-Army-1916-1024x691.jpg)
Here, on a table set up outside a steel helmet factory in Lubeck, Germany, a display is set up, showing the varying stages of the helmet-making process for Stahlhelms for the Imperial German Army.
Rare Historical photos:At the beginning of World War I, none of the combatants were issued with any form of protection for the head other than cloth and leather caps, designed at most to protect against saber cuts. When trench warfare began, the number of casualties on all sides suffering from severe head wounds (more often caused by shrapnel than by gunfire) increased dramatically. The French were the first to see a need for more protection — in late 1915 they began to issue Adrian helmets to their troops. The British troops followed with the Brodie helmet. And later the Germans.
The man responsible for the design of the German Stahlhelm was Dr. Friedrich Schwerd of the Techincal Institute of Hannover. In early 1915, Schwerd completed a study of head wounds that were the result of the trench warfare and submitted a recommendation for steel helmets. He was ordered to Berlin shortly thereafter. Schwerd then undertook the job designing and producing a suitable helmet steel. In some respects, it was an advantage for Germany to have a chance to test both the English and the French types before making conclusive decisions of its own, judging that both designs were far from adequate.
![Stahlhelm, the stages of the helmet-making process of Stahlhelms for the Imperial German Army, 1916 2](https://www.thevintagenews.com/wp-content/uploads/sites/65/2015/10/Stahlhelm-the-stages-of-the-helmet-making-process-of-Stahlhelms-for-the-Imperial-German-Army-1916-2-1024x337.jpg)
The design of the completed helmet included three sections: the dome, the visor and the neck guard. The dome was the main head covering and was cylindrical in shape and somewhat flat on top. The visor extended out to provide shade and protect the soldier against bad weather. It also acted as an open shielded against fragments. The neck guard flared out below the brim, which provided more protection around the neck and ear area.
The basic helmet shell is formed from one steel disk, and went through at least nine stamping stages before it reached its final shape. The complete M-16 weighed 2 pounds and sic ounces (1.08 kg). The color was field green, and the metal was composed of manganese, nickel, silicon, and carbon steel, which was often referred to as nickel steel. Its thickness was between .40 and 0.45 inches (1-1.15 cm), and it is believed to have been pressed hot on electrically heated dies and later dipped into a mixture of japan for the antirust finish. As a result the Stahlhelm had a greater unit cost than the British helmet, which could be formed in one piece.
Helmets were referred to as “shells” when they were empty of any liners and straps. The M-16 shell was manufactured in six sizes: 60, 62, 64, 66, 68 and 70. The sizes were engraved on the inside of all of the shells, and manufacturer’s identification could be found along with it. The inscription was on the left side of the skirt. There were eight factories involved in the manufacturing, therefore, eight different code letters. The head size was never marked in the shell, only the bowl size. It was the metal liner that offered the correct head sizes.
The chin strap. All M-16 helmets were equipped with one style of chin strap. The strap was the same type found on the leather spike helmets. It consisted of a strip of leather looped around the two slide buckles and connected to each end by means of attaching “eyes”. These were fastened to the inner side of the neck guard to specially mounted lug bolts. Since the straps were detachable, many were lost, and so replacements were commonly provided.
The lining. The lining inside the M-16 helmet offered a cushion and the glove-tight fit necessary for wearing steel headgear. This consisted of a mounting band of leather or steel that ran the length of the inner wall of the shell. In addition to the comfort and the safety designed into the M-16 liner was the ease of changing the fitting. If the soldier felt that the supporting cushions were too hard or thick, he was at liberty to remove some of the stuffing to whatever degree he pleased.
Side lugs. No other feature is as recognizable on the M-16 as the side lugs. They stand out and are quite impressive. The lugs served two functions. The first function was for ventilation of the helmet; and second function was to support a heavy armored plate, called a Stirnpanzer. It was thought that this armor would protect sentries and machine gunners who were more exposed to enemy fire than other troops. Generally the soldiers threw the armor away at the first opportunity, as wearing the cumbersome armor in the trenches was of dubious value.